dpy

Circle Text

85 posts in this topic

Fonts... Italianno... I just installed this in Windows. New font is available in Word, Paint.Net, others, but not CircleText.

 

Shouldn't CircleText just pick up the new font?

 

It's my understanding that plug-ins in Paint.net can only use TrueType fonts and not Open Type fonts.

Your new Italianno font is probably otf...

2

Share this post


Link to post
Share on other sites

It's my understanding that plug-ins in Paint.net can only use TrueType fonts and not Open Type fonts.

Your new Italianno font is probably otf...

 

Right you are!

 

I downloaded a TTF version and voila...THANK YOU!!!

0

Share this post


Link to post
Share on other sites

Still having problems with letter spacing along a circle.  Any suggestions welcome...

You can see the problem in the attached image... No space between OMMU and too much space between NIT

Tried different fonts but not successful. If I make the letters skinnier (change font) they don't match other text in the image.

 

Thanks!

 

 

Community Spacing.jpg

Edited by RoyGBiv
0

Share this post


Link to post
Share on other sites

^^^^^

 

I've tried adding spaces, but that seems to compress the letters together proportionally.  The "OMMU" letters begin to merge before the gap in "NIT" closes enough to look right.  I'm trying to build the graphics for an embroidered patch, so each letter needs to remain separated from the adjoining letters with even spacing across the entire line of text.

 

I've also tried playing with changing the angle of arc in conjunction with adding/removing spaces, but the result is the same squashed "OMMU" before I can close the gaps in "NITY".  I can use "skinnier" fonts to hide the problem (still shows the problem but to a lesser degree), but those fonts don't look right with the rest of the patch that contains some other text I cannot change. 

 

It makes good sense that this is happening.... Programatically I assume that the plugin is reserving the same space for each character and "OMMU" fills the available space while the "I" in the middle of "NIT" occupies only the center of the same size reserved space.  I'm not sure how normal (non-curved) text handles this dilemma.  I'd guess that when I'm typing this post the total space allocated to the letter "I" is smaller than the total space allocated to the letter "M" and that is not what is happening with this plugin. "COMMUNITY"  not "COMMUN I TY".  I'd again guess that in normal type, the space for each letter varies in a way that accounts for the actual width of the letter, plus some equal spacing to the right and left, measured from the edges of the letter and not from the edges of a same-sized reserved space that is universal regardless of the width of the letter itself... ?? 

 

It appears that the plugin is holding the same space for "I" and "M", and then adding the same space on either side of both letters when "I" should be assigned less space than "M", plus the same spacing on either side.

 

Apologies for the rambling.... My coffee is just kicking in.  ;-)

Edited by RoyGBiv
0

Share this post


Link to post
Share on other sites

You need to trace a circle that will match the arch of your text in your original image. This circle will be used as a guide.

Copy this circle to a new square canvas.Make sure it is in the center.

I am using the pink circle as an example.

Use the Circle Text plugin and type your word and make it surround the pink circle guide as in the picture on the left.

Duplicate your layer and erase the letter C on  the upper layer.

Erase the letters OMMUNITY on the lower layer.

Go back to the upper layer and Select the entire canvas and rotate your text until the O of OMMUNITY is very close to the C.

Merge the upper layer with the lower layer and...

Repeat the same steps for the rest of the letters.

When you are donne copy it to the clipboard and paste it on your original image.

 

 

circle-text-community-5083035.png

 

Edited by Eli
3

Share this post


Link to post
Share on other sites

Eli... First, THANKS!  I think your suggestion is cleaner than the one I did....

 

I wound up using the circle text feature and then going back and adjusting the letter spacing manually..

1. Rotate image so that I can capture a letter using a square box or lasso.

2. Capture one letter at a time.

3. Adjust the letter location and rotation as needed

4. Repeat.

 

Had to adjust OMMUNIT.  Finished product looks fine, but Eli's way would have been easier.

0

Share this post


Link to post
Share on other sites
23 minutes ago, jeestring said:

Can't see TEXT in effects...

The Circle Text plugin is located in the "Text Formations" submenu. No plugins (that I'm aware of) are using a submenu called "TEXT".

 

Please ensure you've installed the plugin correctly. If in doubt, here are some verbose instructions:

http://www.boltbait.com/pdn/InstallingEffects.asp

 

1

Share this post


Link to post
Share on other sites
On 9/28/2016 at 0:25 PM, Eli said:

You need to trace a circle that will match the arch of your text in your original image.....

etc etc etc.....

 

Wow! I am so glad I came to this forum and discovered that I am a truly lazy SOB!
I did NOT do any of the suggestions, deleted the plugin and found something else far easier and simpler to make my curved text.
And here I thought it was going to be easy...

pn1.jpg

pn2.jpg

0

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now